Heat Shrink Rear Window Film

Take an extra half hour go slowly and the install will be better.

Heat shrink rear window film. Use the heat gun on the outside of the window to warm the adhesive and tinting on the inside. Notice how the film begins to shrink starts to create a little squiggly lines. Normally the heat shrinking is needed when the contour of the glass curves horizontally and vertically like the rear windows of most modern cars. One important consideration to keep in mind is that window film will only shrink correctly towards the factory straight edge.

Learn how to shrink a back window class with our one day heat shrinking rear window class. Heat Shrinking Window Film Warning Never use a heat gun on laminated glass such as windshields and certain Mercedes back glass. Squeegee the film so it is flat against the glass. If you heat the film on the rear window leave the liner on and use a hard card to shape the film to the curved rear window.

Ive been looking online for whether or not you actually have to heat shrink the window tint for the rear window. Anchor the film onto the window along the h shape. The film can be applied in strips smaller strips of tint film overlapped upon each other horizontally or with one single piece of film using a heat gun to shrink and stretch the film to precisely conform to the glass. Begin by taking an uncut piece of tint spray both sides with soapy water and lay it on outside of the rear windshield liner-side up.

With the actual heat itself we are going to break down the first section. In this video we learn to heat shrink a rear window tint. Repeat with the other side. The technique is to wet the window with solution lay the film on the outside with the liner up and the film across the window not up and down trim the pattern and then a heat gun is used to remove fingers.

1 When heat shrinking the rear window of a car the factory edge shows the machine direction or the direction the film will shrink. 11951 Hill Top Rd Suite 20 Argyle Tx. The only way to avoid using strips on a compound curve window is to use the heat shrinking method. How to heat shrink a rear window.

Next rinse with car with a soapy cloth and spread on the lather. These kits include a clear window wrap also referred to as window shrink film adhesive and easy to follow instructions. Very simply the soap method. Use a hair dryer instead.

The wet shrink method is the most commonly used rear window technique. If you heat from the inside you take the risk of melting the tint to the window. I am going to start with the lower bottom of the window. It works very similarly to the Dryer sheet method but since dryer sheets are very toxic the soap method should be used instead.

First prep your window using soapy water. Im finding mixed results. Next lay the window film down with the liner side up. I want to keep that on an even heat and with your hard card apply.

It involves using a heat gun to shrink the excess film along the grain toward the factory edge and smoothing it out with a rolled up paper towel or a bondo card. Based on experience and equipment there are two ways tint can be applied to these challenging rear windows. SnapTint provides pre-cut tint kits for any model and year along with great instructions. I was at the auto parts stored and asked a guy i know that works there about it and he said that it didnt matter really he said.

Shrinking Window Film using the Soap Method. Lift one side of the film and spray the glass with the soap solution. To view the next video in this series click. I have tinted windows before but have never done the rear window.

Smooth out the film using your hand and repeat the above 2 steps until the window film has formed to the shape of the window. The manufacturing process stretches the film primarily in the direction it is wound down into shorter rolls. By far the best method to heat shrink window film for the rear window is the Mdog soap shrink method. Automotive window film installation manual - Rear Window wet shrink Some windows are completely flat and will not require to be heat shrunk.

We realize if a window tint installer is not proficient or does not know how to shrink a rear window. Next create an anchor by dampening in an h shape. If any fingers remain use the heat gun the shrink them start from the. For most kits installation is as simple as applying the window shrink wrap with adhesive and then using a blow dryer to shrink and seal the wrap to the window.

Our quick tutorial on how to heat shrink a pre-cut rear windscreen window tint using the soap methodWe are the UKs leading supplier of pre cut window - buy. Some are saying yes and some are saying it doesnt matter. Try to keep the heat gun between 4 to 6 inches from the glass and heat until the window is warm to the touch. You have got your trusty heat gun and you have got your hard card.

This is an advanced technique and best left to a professional. At Accurate Detail and Tint Inc.

If you re searching for Heat Shrink Rear Window Film you've arrived at the right location. We ve got 15 images about heat shrink rear window film adding images, pictures, photos, wallpapers, and much more. In these page, we also provide variety of graphics out there. Such as png, jpg, animated gifs, pic art, logo, blackandwhite, translucent, etc